GLP Tech News 2022/06/24 [JDC1, FR1, D3Prog]

GLP Tech News 2022/06/24 [JDC1, FR1, D3Prog]
Open in Browser

 

Tech News - 2022/06/24


Dear ,

Please find important technical information below.

Many thanks in advance for your kind attention.

JDC1 Firmware Update 

Main changes from V1.91 to V1.95

FEATURES 

Added: Display Lock
Push Button 1, 2 and 4 together to lock and unlock the display

BUG FIXES 

Solved: Maximum temperatures were not shown correctly in the information menu. 

UPDATE PROCESS

1 file has to be updated via DMX/RS485:

JDC-1 Main DMX V195_F1_71_20_F4_72_22.bin (via D2PROG or D3PROG)

When importing the bin file to a DProg, make sure that you choose the file type BIN before uploading the file to the programmer.

Fixtures can be updated daisy chain via DMXPlease make sure that no other DMX receivers or consoles are active on the line.

If your fixture is on V1.78 or below you have to update the Bootloader first before updating the main application (JDC-1_Main_UpData_BlV3_V4.bin via D2PROG or D3PROG).

INFO

Please take care with the new RDM commands. Factory Defaults will set back DMX start address and DMX Mode to defaults!

If the fixture is still on version 1.78, still, please update the Bootloader first!

DOWNLOAD

GLP JDC1 Firmware V195 Rev20220623-1  zip | 426.82 KB)


impression FR1 Firmware Update

FEATURES 

  • Increased the minimum display contrast to 30
  • Increased the minimum display wait to blackout time to 10 seconds 
  • Before it was possible to set to 0 seconds which caused an immediate display blackout

BUG FIXES 

  • Fixed: bug in the performance settings
  • Fixed: Pan Movement position was calculated wrong in some circumstances
  • Reduced movement noise on Pan/Tilt
  • Fixed Bug in RDM

UPDATE PROCESS

Update can be done via DMX/RS485 with D3Prog Version 42 or higher.
When importing the bin files into a D3Prog (Version 42 or higher) please make sure that you choose the file type BIN before uploading the file to the programmer.

Two Files have to be uploaded in sequence.

First the main file, second the motor file.
(FR-1 Main V124.bin, FR-1 Motor V17.bin )

INFO / Warning - Major Update

This Update is show critical because of fixing bugs in the performance settings.

DOWNLOAD

GLP impression FR1 Firmware V124 Rev20220623-1 (zip | 521.07 KB)


D3Prog/pa Firmware Update

Main changes from V42 to V49 and pa6.12  to pa6.21

FEATURES

This firmware combination allows to work on Windows 11 systems

BUG FIXES 

Solved: Preliminary software release versions (below V 1.0, e.g. 0.11.4) are displayed correctly

UPDATE PROCESS

Programmers running V42 can be updated with the update function of the pa software to V49 if a bootloader V3 is installed already. After the update is transferred , please wait at least 30 seconds until the D*Prog resets on its own.

The bootloader version can be checked in the special menu of the DProg.

If this Bootloader is not installed the bootloader has to be updated ISP, first, with a second DProg.

FURTHER INFORMATION

We suggest to store the executable programmer application V6.21 in a folder together with the ftdi driver, ftd2xx.dll. Usually no further action is needed. Just in case, you can install the driver manually, or execute the CDM21228_Setup file from FTDI

DOWNLOAD

GLP D3Prog Firmware Rev20220622-1 (zip | 10.02 MB)


Copyright © 2022 GLP German Light Products GmbH, All rights reserved. You are receiving this newsletter because you have either ordered it on the website or have a business relationship with GLP (or both).

You no longer want to receive our news? - Unsubscribe